Search results

I tried using 1V and it shows a short consuming 1.3A however went to all the components on the board and didnt find anything heating I am using thinner instead of alcohol since it's more cost benefit down here in Brazil. Could it be the problem? Sorry that I dont have a thermal cam. Should I...

I touhght you mention Short resistance is low enough to start with 1V, that is, go higher at first. Am I getting you wrong? Now you tell me to start with 1V? Ok will start with 1V

Can I start with 3V? 2A is what my PSU also has. Is this enough? I do not feel safe to go over line voltage limit. I think I will keep it to 3V if you agree. Sure I will follow boardview and use thinner to be honest with you! I use thinner more than alcohol Will just put a new U8200 after...

Sure Still have some questions. I should replace U8200 after solving the short on 3V3_G3S right? or it doesnt matter? I do not have thermal camera, how to properly find this short? Injecting volts and putting some alcohol on the componentes that interconnected to 3V3_G3S? Have a better way...

I was going to replace U8200. Removed it But still have a short on PP3V3_G3S = 0.002V Knowing that we still have a short on PP3V3_G3S... could U8200 be good and the problem be around these line? How to move forward from that?

Its a short between S and D. Sorry for my confusion Should I replace U8200?

It looks like shorted 3V3_G3S/G3H_RTC. Not sure what you mean by S-D. However all pins are 0.002 on U8200 except PIN 2 (P3V3G3S_EN) = 0.548

PP3V3_G3H_RTC = 0.002 = WEIRD PP3V3_G3S = 0.002 = WEIRD PP1V8_SLPS2R = 0.180 = A BIT LOW PP3V3_S4SW_SNS = 0.525 = OK PP5V_S4SW = OL = OK Those are the measurements. Let me know if you need anything else more from the Power FET page

The coils around U7800 as below L7824 = 0339 = PVCCQSSD_SW0 = OK L7823 = 0.330 = P0V9SSD_SW0 = OK L7821 = 0.137 = P1VPRIM_SW0 = OK L7820 = 0.248 = PVPCORES5_SW1 = OK L7813 = 0.180 = PP1V8_SLPS2R = A BIT LOW 0.351 OPENDATA L7817 = 0.050 = PP0V9_SLPDDR = OK L7814 = 0.257 = PP1C1_SLPS2R = OK...

L7030 = 0.490 = CHGR_LX1 = OK L7702 = 0.043 = PVCCEDRAM_PHASE = OK L7420 = 0.003 = CPUGT_SW2 = OK L7410 = 0.003 = CPUGT_SW1 = OK L7220 = 0.003 = PPVCC_CPU_PH2 = OK L8100 = 0.200 = P1V2_PHASE = OK L8410 = 0.815 = PPVIN_SW_LCDBKLT_SW = OK L9080 = 0.391 = PPVCC_SW1_TPS62180 = OK L9081 = 0.391 =...

I dont have a good board to compare Can I grab the diode mode readings and posting here?

Removed F7000 and it's 12.25v stable on C7050

Do I need battery connected to check if C7050 is stable since it's PPVBAT line? I am working with the bare board on the bench by the way and the USB-C connector to power the board.

Yes both ports have the same behavior

Actually it goes to 12.23 stay for 2 seconds... drops to 8V stay for around 2 seconds too and the LOOP never ends

I do have a MBP A2289 (820-01987) which is not turning ON has around 5.15v on the USB-C connectorI tried DFU to see if have any behavior on Apple Configurator. Nothing happened PPBUS_G3H = 12.23 and drops to 8 in a constant loop 3V3_G3H_RTC = Goes to 1.7v and drops in a constant loop

I do have a scrap board of 3787 Since its seems to be the same model and year however for MBP 15 inch. I think it could work. If so can I use it since it's the only closest SMC that I do have?

Hello I am creating the USB stick right now. However there is no 3462 file for the SMC Also if you go to the SMCTool website There is this warning. Not sure If I can find it anywhere else

Since I do not have a exact same model donor board. I am thinking to go with this SMCTool. I think I able to create the USB stick with the tool But since its a board with a NAND. I will not be able to remove the HD/SSD from it. Is there an issue doing it that way? How about specific flash...

Replaced the SMC with another one with the same schematic description from a board 820-00165 Now the machine is turning on.. I do have greenlight HOWEVER its really SLUGGISH and If I try to turn on only using the battery without the magsafe connected it goes to login and starts loading the...