Search results

- PM_RMRST_L - 3.32V - PM_PWRBTN_L - 3.32V When I short SMC_ONOFF_L to ground at SW5200, PM_PWRBTN_L (measured at R1802) goes to a few millivolts while I hold the short. It then comes back to 3.3V when I release the short.

So somehow I now have S5_PWRGD but I don't have P5VS4_PGOOD, and R7802 is approximately 100K. I then found that P5VS4_EN_RCD is missing , and more importantly that PM_SLP_S5_L (its dependency) is missing. Could you please point me what PCH signals need to be present for PM_SLP_S5_L to be...

Happy Thanksgiving! I bought an A1707 that was liquid damaged. It sometimes turns on after leaving it alone for a while (albeit doesn't boot, but that might be a separate problem). Right now, these are what I probed for (not in order). It shows 0.05A and 20V from the USB-C meter. I poured...

Hi, I have an 820-00239-A that works minus two pretty big issues. Issue 1: When I plug in my charger or my flash drives, things work great independently. When I plug in my flash drive and charger together, it fries my flash drive and sends 20v straight to the drive (already fried 3 drives...

Everything near U7100, U7210, and U7220 looks really clean. CPUVR_SWSA - L7270 - 1.10v PPVCCSA_S0_CPU - R7270 - 1.03v CPUVR_PGOOD - 3.02v CPUCORE_PWM1 (the PWM pin to U7210) - 2.48v (measured as DC) CPUCORE_FCCM - 14.1mV (600k to ground) - Another clue I am guessing contributing to why I'm...

Hello folks, I recently bought a water damaged A1706 touch bar that doesn't have any chime (and obviously no display or fan). When connected to a USB-C monitor, the monitor turns on but no display (indicating its drawing some power). Here are the measurements I took - do you have suggestions on...

That's unfortunate, okay thanks.

Hmm if the GPU is dead it wouldn't work with an external monitor though, that's why I thought there may be hope.

Yep the voltages were measured with the internal LCD connected and board flipped around

Neither the data lines nor the PP5V_S0SW_LCD resistance - I thought those should be measured without the LCD connected - will redo those measurements then. All the voltages above were done with the LCD connected and the board flipped around - I'll also order another flex cable in case Apple...

Oh very interesting, thanks for the hint! Below are the measurements once again while lid is open and external monitor connected. 5V_S0SW_LCD - 5V for a second PP3V3_S0SW_LCD (R8520 Pin 2) - 3.3v for a second DP_INT_HPD (R8501 Pin 1) - 3.3v for a second EDP_PANEL_PWR_EN (R8510 Pin 1) - 3.1v for...

I bought an A1708 laptop (from original owner in person) for my personal use. 1) The original symptom was the screen would occasionally have a glitchy-looking screen until you move the display (indicating an issue with the flex cable). 2) Took it apart and (don't ask why, I was an idiot) while...

Fixed! One of the resistors (R5875) near the right fin stack on the schematic was loose and fell off. Soldered it back on and it works again :)

Sorry I meant I cleared the part part between the $SVS tags, I thought that was the ME region. I didn't touch anything else.

Hey, I got an 820-4924-A motherboard with possibly some liquid damage and just did a Bios ME Region clean (since it had an EFI lock in it). Battery charges and it runs off battery so I was happy, but now I am running into a new issue. The system is running very slow and kernel_task is using up...

I recently got a liquid damaged board which I got to the state of turning on and working. However, when I hook up two separate batteries, both are saying "not charging" and "replace now". When I look at System Diagnostics it shows current draw is 0mA. Things I checked: pin 17/18 of U7100 =...

Hi Everyone, My retina A1425 is not charging (but recognizes them fine), so I bought 2 new batteries and neither of those are charging either. Please let me know if you have any ideas, I am totally out :( Not sure if it helps but the fan is also spinning in full (might be because the logic...

Oh okay thank you duke :(

Hi Guys, I recently purchased a "new" 820-3462A board (for the 2013 mbp retina) and for some reason my OSX installation went perfectly ok, but when I boot I get all sorts of weird artifacts on the login screen and when I move windows around quickly. I've already reinstalled twice and upgraded...

No I don't have another DC in board, but I tried the same dc in board on a donor 820-3462-A and it gives a green light. EDIT: AHA! Looks like something is pulling the 3.2v from the charger to be 1v. I just need to find whats pulling it down. EDIT: I got 18v!! Just for future reference, read...