Search results

This is driving me crazy!, I disconnected the battery to see if it had something to do it turned on fine, but a few minutes and it restarted and froze loading the user again. This morning I connected the usb c to one of the ports, it went from 5v to 19.4v but 0 A. I changed to another port and...

Sorry, the thing is the computer is now working, I replaced C7609 and is turning on now, it worked fine for 2 days, I turned on today and it is doing a weird thing: when I connect the usb c charger, it goes directly to 19.6v, the amperage shows the following consumption aproximately: it starts...

I removed L7410, the short is gone on PPBUS_G3H. Measured ohms on L7410 PIN 1 = 420 PIN 2 = 1.6 diode mode on: F7000 PIN 2 = .165 L7410 PIN 1 = .002 L7410 PIN 2 = .165 This means dead CPU right?

Hi again, I got this motherboard, it had corrosion on R7109, cleaned the pads and changed the resistor. Still getting short on L7410, 7420 and 7430 Diode Mode on those coils are: L7410/7420/7430 = 0.02 Edit I found out that PPBUS_G3H_CPU was shorted too what lead me to PPBUS_G3H. Removed F7000...

Missing PP5V_S4, but the enable signal is not present... which comes from PM_SLP_S5_L which has a value of 0.183v

Diode mode L7600 = .423 I changed C7609 and now when I connect the charger, it starts at 5v and then jumps to 19.63v but still no sign of it trying to turn on as I get 0 Amp of consumption. ** I used a 0.1 uf 16v, instead of the 0.1uf 25v, because I couldn´t find any exact match on the donor...

Hi, I have this computer which was working fine after I replaced a blown component R7609, it worked fine for a few days (I left it on and working for around 4 days), but when I left it off for 2 days and it doesn´t turn on again. When I connect the charger to a USB C with the USB C tester it...

Removed F7040 and PPBUS_G3H was 12.34v and going slowly up. It took around 5 minutes to get to 12.56v the strange this is that it is still going up slowly... it got to 12.61v and going slowly up... I disconnected the magsafe...

I don´t have the medusa, but have a programmer. Where do I get the BIOS? I reinstalled the U9600, now I get a quarter fan spin, and when the spin is about to start spinning PPBUS_G3H goes from 12.60v to 12.30v, does this means it has something to do with the SMC?

Where can I find the reliable steps to disable it via BIOS?

Using original 85 watt magsafe charger... Its 10 ohms each, between them it is 20.7 ohms

I tried SMC bypass, no luck, still getting quarter spin, no orange light when the battery is connected... I reballed the SMC, nothing... doing the same... what else to check? Thank you!

Hi, I have this 820-2915 and I have green light, the fan spins, but in this model the fan normally starts for a couple seconds then stops, and start again. It spins but doesn´t stops to make the POST. PPBUS_G3H = 12.6V ALL_SYS_PWRGD = 3.3V PLT_RST_L = 3.3V I REMOVED U9600 SEEMED TO HAVE...

I meant, while I am working on them to not kill them when I connect the charger, that could happen because of PPBUS_G3H was high?

Ok, to avoid this happening in other motherboards of this model, what can be done?

sorry I missed that one... so is there anything to do? Hail Mary maybe?

Hi on this board I have quarter fan spin, checked already R7021/22 - right values at 10 ohm R7051 - 2.5 ohms r7052 - 0.2 ohms PPBUS_G3H is 12.63v but goes low to 12.0v and when it goes up again, the fan tries to start... any ideas?

L7630 PIN 1 0.5 ohm, PIN 2 10 Kohm

is there a way of protecting the cpu/pch when testing with the PSU? I´ve had now 2 of the same year and model which ended being PCH. It´s frustrating, because it was off, but I don´t know if maybe something I did kill it... Thanks for your comments...

just to be sure, I removed L7630 and the short is on PIN 2 in diode mode PIN 1 is .248 it´s dead right?