Search results

Yes I meant .859v replaced C9560 that was the first thing I changed after tps and isl6259 On L8920 =.985v PPVCORE_GPU_REG_R

Yes with both battery and MagSafe connected I do see it going from 1.18 to 8.59 It doesn’t appear to be charging J695” Pin 1-3 11.22v steady Pin 4 is 3.42v SMCBUS_SMC_BSA_SCL Pin 5 is 0v SYS_DETECT_L Pin 6 is 3.42 SMCBUS_SMC_BSA_SDA

Only vcore with battery connected not on charger

Nothing smc bypass held power pads for almost 20 seconds and nothing The coils near heatsink 0v Only have 12.55 Coil near fuse 5v Near pch 3.3v near usb PPVCORE_S0_CPU=0

Yes it’s 85w reported on another board. I checked in system report. SMC_CLK32_R=32.2khz I tried checking PCH_CLK25M_XTALOUT_R= no clock signal PCH_CLK25M_XTALIN=no clock signal PCH_CLK32_KRTCX1=no clock signal

Yes it works on other machines And yes it works on other machines I will check with oscilloscope today

No I have two original chargers And this board will not power on. PIN 7 SMC_CLK_R =1.49v ?? Here I expected 3.3v Also I also tested the crystal and it had no voltage on 3pins I will test frequency when I get back I’m gonna go back over these I think these Lin Which I believe should be 3.3v...

The voltages are without battery present. I added a few other measurements on the first post U5010 PIN 1 PP3V42_G3H_SMC_CLK_F =3.42v PIN 7 SMC_CLK_R =1.49v ?? Pin 12 PP3V42_G3H_SMC_CLK_F = 3.42v

Hi I recieved this board it had a few issues I replaced isl6259 and tps51125 And a few resistors. Now I have PPBUSS_G3H =12.5v PP5V_S5=5v PP3v3_S5=3.3v SMC_ONOFF_L =3.42v SMC_RESET_L =3.42v U5010 PIN 1 PP3V42_G3H_SMC_CLK_F =3.42v PIN 7 SMC_CLK_R =1.49v ?? Pin 12 PP3V42_G3H_SMC_CLK_F = 3.42v...

Ok I’ll check all that out tonight thank you For your help.

Yes I plan to do a clean Me on the new chip I just wanted to have the old Chip in case I had a issue to swap back :) thank you for your help

Ok I tried replacing the above component it was in fact reading the same 8ohms I replaced it with a 0ohm 201 resistor and it’s the same issue no camera detected. I will order a new bios chip and switch out the old one with new. I still have to try smc reset but I’m my short experience never...

ok I will :) thanks after reading post he mentioned that replacing R2042 Repaired the camera. I will check R2042 or equivalent on 820-00165

Hi I know I posted this earlier last month but now I have two with the same issue :/ Camera not recognized. I just finished testing 2 -820-3437 and the FaceTime works fine :/ I tried PRAM and installed a new OS X on my test drive Both 820-00165 where water damaged but no where near Anything...

3.42v .I have a green light and All rails are present. I also have fan spin. so my other two questions.TPS22920YZPR from digikey compatible ? Also Same question for u1950 from digikey I’m ordering some parts from the for another project and was wondering if these chips are compatible? Or just...

Hi I got this board and it has no green light PP3V42 .9v I found a cap C5002 shorted and removed it :/ I didn’t find corrosion around smc. It looks like it’s been tossed around parts are knocked off and u2940 is cracked. I don’t have this size caps or a donor board yet i need to order one is the...

Ahh ok thanks. I was reading up on in to see if it was needed. But no I’m not working on Any hackintosh Thank you.

first I’m not sure this goes in this section of the forum. but what are you thoughts on using hwsensor? Is it good? What about the plugin FakeSMC? Is it worth the trouble installing ? Or is there something better? thank you for your time

Resoldered u8900 worked like a charm Thank you sir

Yes I read those threads also I saw that it was a “direct order” But, I just found it odd that all had the same symptom Missing year and model :/ I thought I had done something wrong and all items being from the same seller :) I’m glad I’m done with these. thanks for your help.