Search results

8.56v on ppbus w out battery. I have no Voltage on pin 2 & 3 of the Q3080. i also have no voltage on DCINVSENS_EN_L

Got a customers computer in, liquid damage. shows green and orange light but will not power on without the battery and when i have the battery plugged in it show a battery logo on the screen and then powers off. it had liquid damage on the battery charger plug. isl is good replaced it with a...

Okay 0v on pin 2 and pin 5 of the Q7707. Defiantly no image on the LCD.

Yes LCD connected for all test results.

Okay your def right about that! i have 3.32v on pin 1 not sure how i miss read that. I did check smc_lid it is 3.32v. i do not have anything on pin 4 and 2 still though

Update i just noticed that i did not put the right reading... pin 5 is 0v and pin 2 is 0v. u2071 i have 3v on pin 5 but 0v on pin 1, would you suspect the u2071 to be dead(i need to look and see how 3vs0 gets to pin 1 if it comes from pin 5 or from the other side of the board)? also pin 2 and 3...

820-00164 customers board, liquid damaged. was a dead board the customer said they were getting there data off after the spill and it died on them in the process. brought back the green and orange light but no fan spin. looked into it and am missing pm_slp_s4_L. I check continuity between the...

1.10v pin 6 0v pin 5

Repaired this board liquid damaged. sold on ebay to a repair shop, buyer claimed the board would not power on for 3 min or something like that. got it back and the shop was using the customers computer for its testing they included a fan that was broken so hence why he thought it would not...

if i remove r9709 or r9708 the short goes away and i get 150k+ ohms at PPVOUT_S0_LCDBKLT. if i replace them there is no change and i did check the parts and i was getting proper ohms from them. if i pull the u9701 the short is still there so the problem is not in the u9701. where the heck...

no external, no chime and no beeps when i put no memory in and the speaker im testing with a good. i think this thing has seen its last days... hahah

Yes, Sorry should have mentioned that it was very badly liquid damaged. some fried stuff and stuff that did not look good. idk not that much in general just more than normal replaced. pretty toasted board to start with. normally i would just toss it and move on. but i have some extra time and...

I have seen the same thing and it did end up being the smc, also double check the solder job is good on it sometimes the balls are just not seating good.

got a 2915 board. no power, replaced lots of parts so far, was missing pp5v and pp5v sus, brought it back replaced the q7802. tracking down the 5v_s3 and traced it back to the PM_SLP_S4_L has no power. I seem to be getting lost trying to track down the power creation for 5v_s3 any help is...

Got a 820-2523 with no video, found there to be no power on the LCD_PWR_EN line. traced it back to the u9600 with no power the entire way. is the u9600 the only thing at this point that would be the culprit? or is something signaling the u9600 to put out LCD_PWR_EN? If it is the u9600 should...

Can i ask why your tech has a mask on and not a proper carbon scrubber setup in that room? seems pretty half ass for a guy using a $70,000 rework station..

Okay thanks TCRS, i tried a re-flow and still no difference. unless anyone has any other ideas i'm going to give this one back almost fixed but unfixed.

I will look into the isl6259 area and current sensing. 8.57v on ppbus with ac only. with and without the system powered on. acok is present at 3.34v. Looking into around the memory im finding corrosion around the chips and u4000 and u3900 all have green corrosion under them, if i scrap the...

no the trackpad flex looks good and the trackpad itself, if i disconnect the trackpad it still does the same thing. there was corrosion in the battery connector, i cleaned that. there was corrosion on the jtag and i removed the jtag. maybe there is corrosion under the trackpad connector? i could...

that few times i have tried to power it up it load to the option menu and then before i can select my drive it keeps dying. Even with a new IO board. tried powering on with everything unplugged and it still crashes. crashes before i can run Diagnostics. PhilipC Did it crash if you had the IO and...