Recent content by repMacFixit

Comparison bad board/Good Board (this board has iCloud lock but works) PP1V5_SPMU_VREFADC - 0.593/0.590 PP0V88_S1 - 0.347/0.3528 PP0V8_S1_VDD_FIXED -0.298/0.300 PP1V5_MPMU_VREFADC - 0.587/0.5915 PPVDD_S2SW_VDD2H - 0.0546/0.06 PP1V2_AWAKE_PLL - 0.4274/0.4343 PP0V855_S2SW_CIO - 0.326/0.3319...

With USB-C PP1V2_AON_SPMU - 1.2V PP1V5_LDOINT_SPMU - 1.5V PP1V5_SPMU_VREFADC - 0.0v PP1V8_AON_SPMU - 1.8v PP3V8_AON_SPMU_ISNS_VIN - 3.8V PP1V25_S2 - 1.25v PP0V88_S1 - 0.0v PP1V8_S2 - 1.8v PP0V8_S1_VDD_FIXED - 0.0v PP0V72_S2_VDD_LOW - 0.75v PP1V2_AON_MPMU - 1.2v PP1V5_LDOINT_MPMU - 1.5v...

My mistake. i was looking for signal lines with LDO around those chips and not the actual port names. Anyway, here are the voltages collected using the MagSafe as power source. PP1V2_AON_SPMU - 1.2V PP1V5_LDOINT_SPMU - 1.5V PP1V5_SPMU_VREFADC - 0.0v PP1V8_AON_SPMU - 1.8v...

PPBUS_AON - 12.0V (Both MagSafe and usb-c) PP3V8_AON - 3.796v (Both MagSafe and usb-c) Not main LDO signals on U8100 and U7700 PP1V5_LDOINT_MPMU - 1.5V PPVDD_LDO20_14_8_3 - 1.25v PP3V3_S2_LDO - 3.3v

Diode mode readings were comparable to a good board. What should the voltage on USBC5_CC1 be (unfortunately i no longer have the good board available)? Away, i'm getting 1.66v on USBC5_CC1. And yes, when the battery is connected, the two usb-c ports did switch to 20V but no current draw.

Got this board, no sign of liquid damaged. The MagSafe light is off but once I plug in a usb-c it goes from 5v with some current draw to 20v but no current draw. This happens on both usb-c ports. The system ran while the battery still had charge. Suspecting the cd3217 chip for the MagSafe but...

Thanks. That helped a lot. Using that link, i was able to isolate it to QP801. It was shorted. Repaired.

Hello Have another one here with backlight issue. I've confirmed the display works with another board and video outputs via HDMI as well. Found corrosion on UP800, replaced along with RP880 and RP833 as they were open. Still not getting backlight. Replaced UP800 again just incase with the...

Thank you and that worked. For future repairs, what flash tool would you recommend for reflashing of U5560. I was lucky this time around, i had a donor board that i could swap with. I currently have a TL866A minipro.

History: Board originally had a blown CD3217 chip. Replaced all 4 and all but U5500 is working as expected. When the MagSafe is connected, the light keeps cycling between green orange and off. PPDCIN_AON cycles between 5v and 0v, while PPBUS_AON cycles between 12.4v and 6.5v Before i replace...